This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| diretta [2025/07/23 06:12] – admin | diretta [2025/07/23 06:25] (current) – admin | ||
|---|---|---|---|
| Line 18: | Line 18: | ||
| As many of you may already know, Diretta is a network audio protocol specially designed for high-quality music playback. This protocol sends music data in small, consistent packets, which allows for lower current usage compared to protocols that send large amounts of data at once. As a result, it reduces internal noise in audio devices and provides superior sound quality. | As many of you may already know, Diretta is a network audio protocol specially designed for high-quality music playback. This protocol sends music data in small, consistent packets, which allows for lower current usage compared to protocols that send large amounts of data at once. As a result, it reduces internal noise in audio devices and provides superior sound quality. | ||
| + | ====== How to Set Up a Direct Ethernet Connection Between Diretta Host and Target ====== | ||
| + | It could be available from the Eunhasu firmware version no.0.5.9. | ||
| + | 1. Prepare an //Ethernet crossover cable// and a USB Ethernet dongle or USB Wi-Fi dongle. | ||
| + | (Note: You can order a high-end Ethernet crossover cable directly from SOtM.) | ||
| + | |||
| + | 2. Upgrade both the Diretta Host and Target devices to Eunhasu version 0.5.9. | ||
| + | |||
| + | 3. If your device has only one Ethernet port, connect the USB Ethernet or USB Wi-Fi dongle. | ||
| + | |||
| + | 4. Open the Eunhasu web GUI on the Diretta Target device and go to the System Config page. | ||
| + | |||
| + | 5. If using a USB Wi-Fi dongle, connect the device to your network via Wi-Fi. | ||
| + | {{ :: | ||
| + | 6. Access the Eunhasu web interface through the Wi-Fi or USB Ethernet port you’ve connected. | ||
| + | |||
| + | 7. Set a static IP address on the Ethernet port that will be used for the direct connection to the Diretta Host device. | ||
| + | Use an IP address like `xxx.xxx.xxx.nnn`. | ||
| + | (Note: The first three sections of the IP address—`xxx.xxx.xxx`—must match the Diretta Host’s IP address. The last number `nnn` must be different from the Host’s.) | ||
| + | |||
| + | Netmask: 255.255.255.0 | ||
| + | Gateway and DNS Server: Leave both fields empty | ||
| + | {{ :: | ||
| + | 8. Click ‘Save & Reboot System’. | ||
| + | |||
| + | 9. Once rebooted, open the Diretta Config page on the Target device. | ||
| + | |||
| + | Set Diretta mode to Target. | ||
| + | Select the Diretta Target audio device. | ||
| + | Click the Save Changes button. | ||
| + | (Note: You do not need to configure the Host Ethernet port on the Target device.) | ||
| + | 10. Click the ‘Start’ button to activate Diretta Target mode. | ||
| + | {{ :: | ||
| + | |||
| + | 11. On the Diretta Host device, open the Eunhasu web interface and go to the System Config page. | ||
| + | |||
| + | 12. Set a static IP address on the Ethernet port that will be connected directly to the Diretta Target. | ||
| + | Use an IP address like `xxx.xxx.xxx.nnn`. | ||
| + | (Note: The first three sections of the IP address—`xxx.xxx.xxx`—must match the Diretta Target’s IP address. The last number `nnn` must be different from the Target’s.)* | ||
| + | |||
| + | Netmask: 255.255.255.0 | ||
| + | Gateway and DNS Server: | ||
| + | {{ :: | ||
| + | 13. Click ‘Save & Reboot System’. | ||
| + | |||
| + | 14. Connect the crossover Ethernet cable between the Ethernet port of the Diretta Target device and the corresponding Ethernet port on the Diretta Host device. | ||
| + | |||
| + | 15. Open the Diretta Config page on the Host device. | ||
| + | |||
| + | * Set Diretta mode to Host. | ||
| + | * Select the Ethernet port you want to use for the direct connection to the Target. | ||
| + | * Click the Save Changes button. | ||
| + | (Note: You do not need to select a target audio device on the Host.) | ||
| + | (Note: If you do not select a Host Ethernet port, Diretta Host will use all available Ethernet ports.) | ||
| + | |||
| + | 16. Click the ‘Start’ button to activate Diretta Host mode. | ||
| + | You should now see the Diretta Target device appear as shown below. | ||
| + | {{ :: | ||
| + | 17. Go to the Music Player Config page, select the Diretta Target device as the audio output device, and click ‘Save Changes’. | ||
| + | This will return you to the Eunhasu web GUI main page. | ||
| + | |||
| + | 18. Start the music player and open its control app on your smart device. | ||
| + | |||
| + | 19. Enjoy the Soul Of the Music. | ||